Oracle 1z0-105 問題集

質問 1：
You construct a new udev rule to name a specific removable device, but the rule does not appear to work.
Which command would you use to troubleshoot the new rule?
A. udevadm control
B. udevadm monitor
C. udevadm trigger
D. udevadm settle
正解：B
解説: (Topexam メンバーにのみ表示されます)

質問 2：
You want to create a new LUN, LUN ID =1, on a new target, target ID = 2.
Inspect the current state of targets and LUNs in the output from tgt-admin -s. The output is filtered
to show only target and LUN associations.
[root@EDFAR9P0 init.d]# tgt-admin -s | egrep -i 'target|lun'
Target 1: iqn.2013-03.com.example.mypc:1
LUN information:
LUN: 0
LUN: 1
LUN: 2
LUN: 3
You want to add a new LUN to a new target by using the /iSCSIsharedDisk/physDisk4.img disk image file.
Which two options would you use to do this?
A. tgt-admin -d /iSCSIsharedDisk/physDisk4.img -n 2
B. tgtadm -- op new \
--mode target \
--tid 2\
--targetname iqn.2013-03.com.example.mypc:2 \
--lun 1 \
--backing-store /iSCSIsharedDisk/physDisk4.img
C. tgt-admin --op new \
--mode target \
--tid 2\
--targetname iqn.2013-03.com.example.mypc:2
tgt-admin --op new \
--mode logicalunit \
--tid 2 \
--lun 1 \
--backing-store /iSCSIsharedDisk/physDisk4.img
D. tgt-setup-lun -t 2
tgt-setup-lun -d /iSCSIsharedDisk/physDisk4.img -t 2
E. tgt-setup-lun -d /iSCSIsharedDisk/physDisk4.img -n 2
正解：A,D

質問 3：
What is function of the System Security Service Daemon (SSSD)?
A. It permits single-user accounts by maintaining credentials for back-end systems on behalf of local users.
B. It enables fingerprint reader support for Kerberos clients.
C. It enables Smart Card Authentication for Kerberos clients.
D. It permits Kerberos authentication to be done offline by caching user identities.
正解：A

質問 4：
Which three statements are true about the contents of the /etc/ocfs2/cluster.conf configuration file?
A. The heartbeat stanza is required only if local heartbeat mode is enable.
B. All parameters must start after a tab.
C. A blank line must demarcate each stanza.
D. A blank line must demarcate stanzas and parameters.
E. All stanzas must start at the first column and end with a colon.
F. All parameters must start after a tab and begin with a colon.
正解：B,C,F

質問 5：
Which two statements are true about building binary RPMs using rpmbuild?
A. Only theROOTuser can install source RPMs.
B. Using customer-complied binary RPMs is not supported by Oracle.
C. A binary RPM for a given hardware platform can be built on another hardware platform.
D. Building a binary RPM will always generate a new source RPM.
E. Building a source RPM always produces exactly one binary RPM.
F. Only theROOTuser can create binary RPMs.
正解：B,F

質問 6：
Examine the contents of the /etc/ocfs2/cluster.conf file: node: name = exam2 cluster = mycluster number = 0 ip_address = 192.168.56.106 ip_port = 7777
node: name = exam3 cluster = mycluster number = 1 ip_address = 192.168.56.107 ip_port = 7777 clustr: name = mycluster heartbeat_mode = local node_count = 2 Identify the minimum number of commands issued, in the correct order, to create this file.
1.o2cb add-cluster --heartbeat_mode local mycluster
2.o2cb add-node --ip 192.168.56.107 --number 1 mycluster exam3
3.o2cb add-cluster mycluster
4.o2cb add-node --ip 192.168.56.106 -- number 0 mycluster exam2
5.o0cb config-cluster -node_count 2 mycluster
6.o2cb configure
A. 6, 4, 2, 3
B. 6, 4, 2, 5, 3
C. 1, 4, 2
D. 6, 1, 4, 2
E. 3, 4, 2
F. 1, 4, 2, 5
正解：B

質問 7：
Which three statements are true about accessing Windows shares from Linux with SAMBA on Oracle Linux?
A. The findsmb utility queries a file to findSAMBAservers.
B. FTPmay be used to accessSAMBAshares on Windows.
C. Thesmbtreeutility queries a file to findSAMBAservers.
D. The password required to accessSAMBAshares on Windows may be specified in themountcommand.
E. The username and password required to accessSAMBAshares on Windows may be specified in /etc/fstab.
F. Thesmbclientutility uses a lowercase version of the environment variableUSERorLOGNAMEif the username is not provided on the command line.
G. The username required to access theSAMBAshares on Windows may be specified in themountcommand.
正解：A,C,F
解説: (Topexam メンバーにのみ表示されます)

質問 8：
You want to configure networking on a host and have these requirements:
1.A cache only nameserver is to be used.
2.DHCP is used to obtain an IP address.
3.DHCP must not overwrite nameserver details contained in the /etc/resolv.conf file.
4.The nameserver must be activated automatically at system startup.
5.There are two network adaptors, eth0 and eth1.
The bind package has already been installed and the network service stopped.
Which four actions must be performed to implement this requirement?
A. Add a line withPEERDNS=noto the/etc/resolv.conffile.
B. Add lines withPEERDNS=noandBOOTPROTO=dhcpto the /etc/sysconfig/network-scripts/ifcfgeth0file.
C. Start thebindservice only automatically by usingchkconfigfor those services at the appropriate run levels.
D. Thenetworkandbindservices must be started automatically by usingchkconfigfor those services at the appropriate run levels.
E. Add a line withnameserver 127.0.0.1to the/etc/resolv.conffile.
F. Add lines withPEERDNS=noandBOOTPROTO=dhcpto the /etc/sysconfig/network-scripts/ifcfgeth1file.
G. Start thenetworkservice only automatically by usingchkconfigfor those services at the appropriate run levels.
正解：A,D,E,G