Network Appliance NS0-194 問題集

質問 1：
Which NetApp Web-based tool would be used to analyze Perfstat output?
A. My AutoSupport
B. SmartSolve
C. LatX
D. Field Portal
正解：D

質問 2：

Referring to the exhibit, the UNIX user "prof1" will be looked up in which source first?
A. ldap
B. nis
C. files
D. dns
正解：D

質問 3：
You have an ONTAP 9.3 cluster and create a new SnapMirror relationship with a SnapMirror type of DP. You initialization the SnapMirror relationship and verify that incremental updates are operating as expected.
However, you notice that the SnapMirror type is XDP instead of the specified DP.
In this scenario, which statement is correct?
A. DP is not supported in ONTAP 9.3.
B. The SnapMirror policy type was set to MirrorAllSnapshots.
C. The destination cluster is running an older version of ONTAP.
D. All new relationships default to XDP.
正解：D

質問 4：
You have a 4-node MetroCluster configuration. The systems are operating normally with no faults.
In this scenario, which statement describes the usage of NVRAM when a host sends a write to a node?
A. Incoming writes are written to the all four nodes' NVRAM.
B. Incoming writes are written to the receiving node's NVRAM, its HA partner's NVRAM, and its DR partner's NVRAMonly.
C. Incoming writes are written to the receiving node's NVRAM and its HA partner's NVRAM only.
D. Incoming writes are written to the receiving node's NVRAM and its DR partner's NVRAM only.
正解：D

質問 5：
A 2-node cluster (Node-1 and Node-2) has suffered a takeover event. The down node (Node-1) is currently waiting for give back.
However, it is unsure if the node will boot successfully. The client suffer any data outage.
Which command would you use to perform the give back?
A. CLUSTER::> storage failover giveback -of node Node-1-require-partner-waiting false
B. CLUSTER::> storage failover giveback -of node Node-1-override-vetoes true cannot
C. CLUSTER::> storage failover giveback -of node Node-1-only-do-aggregates
D. CLUSTER::> storage failover giveback -from node Node-2
正解：A

質問 6：
You are migrating volumes from an older aggregate to a new aggregate using the vol move command. You notice that, after completion, access to these volumes is slower until a certain process finishes.
Which process is causing the problem in this scenario?
A. deswizzling
B. active bitmap rearrangement
C. snap create
D. container block reclamation
正解：C

質問 7：
Exhibit:

A customer receives the AutoSupport message shown below.
''(?] Sat Aug 23 13:00:27 PDT [hostname: env_rngr: callhome.c.fan.fru.fault:error] :
Call home for CHASSIS FAN FRU FAILED: SysFan3 F2 (?] Sat Aug 23 13:00:32
PDT [hostname: env_mgr: monitor.chassisFan.ok:notice]: Chassis fan Sysfan3 F2 is ok"
The output of the sysconfig -a command is shown in the exhibit.
In this scenario, what would you do to solve this problem?
A. Disconnect the controller from the mains, wait two minutes, and re-connect it in the next maintenance window.
B. Update the Service Processor firmware.
C. Update Data ONTAP to 8.1.4 at the latest patch level.
D. Replace the fan.
正解：C

質問 8：
A customer created a new storage virtual machine (SVM) named "svm-nfs". They enabled only NFSv3 and created a new export policy called "Linux". In this policy, they created a rule replacing the default rule that shows the host specifier to be IP address 172.16.100.0/24.
This configuration has worked well for the past two weeks for all Linux clients. A new Linux client is about to be put into production but it is not able to access the NFS mount. The root user on this new client is not able to mount as well. They receive the "access denied" error.
Which statement is correct in this scenario?
A. There is no export policy entry for the namespace for this export.
B. The time on the controller is skewed by more than five minutes.
C. The new client's IP address is not in the same subnet that is specified in the export policy rule.
D. The volume is NTFS security style.
正解：C