Riverbed 199-01 問題集

質問 1：
You have outgrown your current Steelhead appliance and want to copy the datastore from your exiting Steelhead 550 appliance to a new 2050 Steelhead appliance.What feature would you use to synchronize the different model Steelhead appliance datastores?
A. "datastore send" command
B. Copying the configuration files
C. Copy the datastore file system
D. This cannot be done on Steelhead appliances
E. Export/Import operation function
正解：D

質問 2：
When would Simplified Routing Destination Only be used? (Select 2)
A. There is no setting for Destination Only
B. Bridged network
C. Multiple firewalls
D. VLAN bridging
E. HSRP (Hot Standby Routing Protocol)
正解：B,E

質問 3：
-- Exhibit-

-- Exhibit -
Refer to the exhibit. A Steelhead administrator has decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the Interceptor appliances, and the Steelhead appliance, he decided to check if the connections are being forwarded appropriately. What happened? (Select 2)
A. The connection was not optimized because of the GRE tunnel.
B. The connection was optimized because of the GRE tunnel.
C. The connection from client 172.16.19.88 to server 172.16.12.99 was optimized by Steelhead appliance 172.16.10.101.
D. The connection from client 172.16.12.99 to server 172.19.88 was optimized by Steelhead appliance 172.16.10.101.
正解：B,D

質問 4：
The exhibit shows a data center side serial clustering deployment.In this organization, not every remote site has a Steelhead appliance deployed, and all remote locations will be connecting to the data center.

For connections initiated from the data center, there is a possibility that the Steelhead appliances shown in the exhibit will end up peering with each other, rather than the intended remote Steelhead appliances.Where are peering rules needed to prevent this problem?
A. A and B
B. A only
C. B only
D. B and C
正解：A

質問 5：
Refer to the exhibit.

SH3 and SH4 are able to optimize HTTP sessions from Client41 to application host Server31.However, Client41 receives a failure messagE. "ftp connect: Unknown error number" while trying to connect Server32.The same applies to Client42.Note that SH3 and SH4 are in auto-discovery mode.Client41 and Client42 are able to ping Server32.What is the most likely cause of this failure?
A. An outbound access-list specified at R3f0 denies FTP control traffic from Client41 and Client42
B. An outbound access-list specified at R3f0 denies IP traffic from Client41 and Client42
C. The FTP service running in Server32 is down
D. The network interface card (NIC) at Server32 is down
E. The routing protocol between R3 and R4 is configured wrong
正解：C

質問 6：
When upgrading from a Steelhead 5050 appliance to a Steelhead 6050 appliance what can be migrated to the new appliance? (Select 2)
A. Datastore
B. Network configuration
C. Optimization configurations
D. Licenses
E. Serial numbers
正解：B,C

質問 7：
When deploying a Virtual Steelhead appliance, how much extra memory should be allocated for the extra VMware overhead?
A. 4%
B. 5%
C. 10%
D. 3%
E. 2%
正解：B

質問 8：
When using SSL, what is the purpose of peer authentication?
A. Authenticate the client to the server
B. Establish sessions
C. Verify the user permissions
D. Register peers
E. Confirm the identity of the peer
正解：E