VMware 2V0-41.19 問題集

質問 1：
Which three steps must be taken to assign a new IP address to a member of a NSX Management Cluster that was deployed manually? (Choose three.)
A. Delete NSX Manager VM
B. Deploy new NSX Manager VM
C. Execute detach node <node-id> from the NSX Manager CLI
D. Change IP address of NSX Manager in vApp Properties
E. Delete NSX Management cluster member from NSX Simplified UI
正解：A,B,C
解説: (Topexam メンバーにのみ表示されます)

質問 2：
An NSX administrator is reviewing syslog and notices that Distributed Firewall Rules hit counts are not being logged.
What could cause this issue?
A. Distributed Firewall Rule Logging Is not enabled
B. Zero Trust Security Is not enabled
C. Syslog Is not configured on the NSX Manager
D. Syslog is not configured on the ESXI transport node
正解：C
解説: (Topexam メンバーにのみ表示されます)

質問 3：
When a stateful service is enabled for the first time on a Tier-0 Gateway, what happens on the NSX Edge node?
A. SR and DR is instantiated but requires manual connection.
B. SR is instantiated and automatically connected with DR.
C. SR and DR doesn't need to be connected to provide any stateful services.
D. DR is instantiated and automatically connected with SR.
正解：B

質問 4：
Which two statements describe the characteristics of the Services Router (SR) component of a Tier-0 Gateway? (Choose two.)
A. SR can be created from the NSX Advanced Networking & Security tab in the UI.
B. Edge cluster is mandatory for SR to be created.
C. Edge transport nodes are required for SR to be created.
D. SR is automatically created when stateful services are enabled.
E. SR can exist on both hypervisor transport nodes and Edge transport nodes.
正解：C,D
解説: (Topexam メンバーにのみ表示されます)

質問 5：
Which is correct when deploying a NSX Edge in a KVM only environment?
A. deploy NSX Edge VM with ISO image
B. deploy NSX Edge VM with OVF template
C. deploy NSX Edge on a bare-metal server
D. deploy NSX Edge VM with QCOW2 image
正解：C

質問 6：
What are two valid options when configuring the scope of a distributed firewall rule? (Choose two.)
A. Tier-1 Gateway
B. DFW
C. Segment Port
D. Segment
E. Group
正解：B,E

質問 7：
What are the supported N-VDS modes?
A. Standard Datapath
B. Enhanced Datapath
C. Secure Datapath
D. DPDK Datapath
E. Overlay Datapath
正解：A,B
解説: (Topexam メンバーにのみ表示されます)

質問 8：
Which three hardware-based offloads provide maximum performance for physical network interface cards?
(Choose three.)
A. Receive Side Scaling (RSS)
B. Source Route Bridging (SRB)
C. Priority Flow Control (PFC)
D. Large Receive Offload (LRO)
E. TCP Segmentation Offload (TSO)
F. Netfilter Flow Offload (NFO)
正解：A,D,E
解説: (Topexam メンバーにのみ表示されます)

質問 9：
An NSX administrator has created a segment named WEB-LS from the simplified UI and noticed the segment is not realized on the KVM Transport node.
What are two possible causes for this issue? (Choose two.)
A. The virtual machines running on the KVM Transport Node are connected to the WEB-LS segment, but are in Powered Off state.
B. The virtual machines running on the KVM transport node are not connected to the WEB-LS Segment.
C. Since the Compute Manager is disconnected in Simplified UI, the WEB-LS segment will not be realized on the KVM Transport Node.
D. The virtual machines running on the KVM Transport Node are not connected to the VDS.
E. The KVM Transport node has hardware issues and will not realize the WEB-LS Segment.
正解：A,C