Nutanix NCM-MCI-5.20 問題集

質問 1：
A VDI environment based on AHV Cluster is not performing well. The current environment is using only one bridge (Bridge0). The administrator needs to verify if nodes are using all network cards associated to Bridge0.
Which two menus should be used to check the current configuration? (Choose two.)
A. Host NICs tab in Hardware menu
B. Network Configuration item in Settings menu
C. Host view in Network menu
D. I/O Metrics tab in VM menu
正解：A,C

質問 2：
How should an administrator enable the recycle bin on a nutanix cluster?
A. Select the enable recycle bin checkbox in the configure CVM page of the cluster setting
B. select Retain Deleted VMs for 8h in the cluster Details Page of the cluster setting
C. Select Retain Deleted VMs for 24h in the cluster details page of the cluster setting
D. Select the Enable Recycle Bin checkbox on the storage Overview page
正解：C

質問 3：
An administrator is using Nutanix Move to migrate a Windows VM from ESXi to AHV. Automated guest preparation is failing with an error:
Account has UAC enabled error
The administrator is using the local built-in administrator account for the Windows VM Admin approval mode must remain enabled.
What should the administrator do to continue with the migration with Nutanix Move?
A. Reboot the Windows VM and try the migration again
B. Follow manual VM preparation guidelines
C. Place Windows VM in Maintenance Mode
D. Use a Domain Admin account for the Windows VM
正解：B
解説: (Topexam メンバーにのみ表示されます)

質問 4：
An administrator is planning to deploy a Nutanix cluster to support a few high-performance VMs. This deployment will have the following considerations:
* Individual VMs will likely generate network throughputs in the range of 90-100Mbps
* Due to the configuration of the VMs, it is unlikely that a node will host more than one or two of them at a time
* Individual VMs will communicate with only a few (one or two) remote hosts at a time
* Multicast will not be used in the environment
* The hosts are connected via two 1GbE network connections
How should the administrator configure the network bonds to meet this requirement while maintaining the simplest switch configuration?
A. Configure bond0 as balance-tcp
B. Configure bond0 as balance-sib
C. Configure bond0 as active-backup
D. Configure bond0 as balance-lacp
正解：B

質問 5：
An administrator is configuring an All Flash cluster to support the following workloads:
* Full clone virtual desktops
* Hadoop
* Write heavy databases
Which three correct configuration options should the administrator use to meet the item requirements? (Choose three.) For each procedure, indicate whether it is a correct or incorrect procedure that must be configured to meet the item requirements using the drop-down option.

正解：

Reference:


質問 6：
A Nutanix cluster is deployed with the following configuration:
* Three four-node blocks (A, B, and C)
* All Flash Redundancy Factor 2
What is the effect of simultaneous disk failures on two nodes located in block A?
A. VM read and write operations continue normally.
B. VMs on the nodes with failed disks are unable to write data
C. VMs are migrated off of the nodes with disk failures.
D. Each node with a failed disk is marked as degraded.
正解：A

質問 7：
An administrator knows that the disks in a cluster are out of date and a new firmware is available. For security reasons, these clusters do not have access to the Internet.
Which two steps must be completed to update the firmware? (Choose two.)
A. Download the updated firmware .tgz file from the Nutanix portal.
B. Download a dark site bundle and stage it on an internal webserver.
C. Configure LCM with a URL to access the firmware bundle.
D. Select Upgrade Software, then select disks and upload the updated firmware.
正解：B,C

質問 8：
An Administrator Wants a VM to Communicate with two Separate VLANs.
What steps should the administrator complete?
A. Add a single NIC to the VM and Configure it for both VLANs
B. Add two NICs to the VM and Configure one for each VLAN
C. Turn on IPAM for auto configuration of VLANs
D. Configure a security Policy to assign VLANs to the VM
正解：B