Network Appliance NS0-181 問題集

質問 1：
Select the Exhibit tab.

The exhibit illustrates the network cabling of a 4-node HA cluster that includes four separate networks.
Which two definitions are correct in this scenario? (Choose two.)
A. A cluster can be created without data network connections, but it must include a cluster interconnect connection.
B. A cluster cannot be created without data network connections, but it must include a cluster interconnect connection.
C. Each node must be connected to five distinct networks.
D. Each node may be connected to the management and cluster networks only.
正解：A,B

質問 2：
After the installation of a new 2-node cluster, you want to make sure that AutoSupport is working as expected from the cluster.
In this scenario, what are two ways to trigger a new Auto Support? (Choose two.)
A. Use the ping command on the mailhost.
B. Use the OnCommand System Manager GUI.
C. Use the OnCommand UnifiedManager GUI.
D. Use the system node autosupport invoke -type test command.
正解：B,D

質問 3：
Your customer has filled out the customer installation worksheet. However, the customer's network environment is not set up and ready for the new ONTAP 9.1 system. The customer requests that you install the system and states that they will finish the configuration when they have acquired the appropriate network connections.
Which two statements are correct about this scenario? (Choose two.)
A. A cluster can be created without data network connections, but it must include a cluster interconnect connection.
B. You should cable a cluster so that the clusters interconnect traffic is on a separate network from all other traffic.
C. You should cable all of the controllers and disk shelves, power on the system, and then leave the system as-is for the customer to configure.
D. You cannot install an ONTAP system without having the customer network configuration.
正解：A,B

質問 4：
You are dispatched to install a new cluster with six AFF A300 nodes. While running Config Advisor, you determine that there is a newer firmware version for 48 SSDs.
Which statement is correct in this scenario?
A. Prior to leaving the site, tell the customer that a later firmware exists for those disk drives, but that the upgrade will provoke downtime.
B. Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.
C. Unless the customer advises otherwise, upgrade the firmware on the SSDs to clear the Config Advisor error.
D. Prior to leaving the site, advise the customer that the firmware is included in the version of ONTAP that they downloaded.
正解：D

質問 5：
You are asked to installed a new cluster with six FAS8060 nodes. While running Config Advisor, you determine that there is a newer firmware version for 16 HDDs.
How should this situation be handled?
A. Unless the customer advises otherwise, leave the firmware alone and document the version of ONTAP being used to explain the issue.
B. Unless the customer advises otherwise, upgrade the firmware on the HDDs to correct the Config Advisor error.
C. Prior to leaving the site, advise the customer that firmware is included with the version of ONTAP they selected.
D. Prior to leaving the site, confirm the version of ONTAP that the customer wanted installed to correct the Config Advisor error.
正解：B

質問 6：
You have just added a new DS4246 shelf with 24 x 10 TB SATA HDDs to a single FAS2650 node as the first SATA shelf. You must keep two SATA spare disks on the shelf.
What is the maximum number of SATA data disks available in this scenario?
A. 19
B. 16
C. 20
D. 22
正解：C

質問 7：
Your customer has a new FAS2650 HA cluster with ONTAP 9.1 installed. The cluster is connected to two CN1610 switches.
Which two statements describe this installation? (Choose two.)
A. The cluster interconnect is in a switched configuration.
B. This is a single-node installation.
C. This is a multiple-node installation.
D. The cluster interconnect is in a switchless configuration.
正解：A,B

質問 8：
You are planning to install a new ONTAP system for a customer.
Which action should be performed before configuring the cluster interconnect switches?
A. Download the software for the Fiber Channel switches before configuring them.
B. Confirm the IP address and configuration information before configuring the switch
C. Use the Inventory Collect Tool before configuring the switches.
D. Use the Config Builder Tool to verify compatibility before configuring the switches.
正解：B