Network Appliance NS0-507 問題集

質問 1：
You are asked to configure the Service Processor on a newly installed node, and must verify the following command:
system-service processor network modify -node local -address-family IPv4 -enable true - ip-address 192.168.123.98 -netmask 255.255.255.0
Which statement about this command is true?
A. -nodeshould reference the actual node name.
B. IPv6 is required for the SP.
C. The gateway IP address is missing.
D. The Link Local IP Address is missing.
正解：A,C

質問 2：
You notice that reporting nodes are not mapped on a LUN in a 4-node cluster that originally ran an older version of ONTAP. In this scenario, which command would you use to add only the local HA pair to the reporting nodes for the /vol/data/lun1/LUN?

A. Lun mapping add-reporting-nodes -path /vol/data/lun1 -igroup igroup1 -all false
B. Lun mapping add-reporting-nodes -vserser svm1 -path /vol/data/lun1 -igroup igroup1 destination-volume cl01_01_aggr1
C. Lun mapping add-reporting-nodes -vserver svm1 -path /vol/data/lun1 -igroup igroup1 destination-aggregate data
D. Lun mapping add-reporting-nodes -vserver svm1 -path /vol/data/lun1 -igroup igroup1-local nodes true
正解：D

質問 3：
You want to create a thick provisioned LUN within a thick-provisioned volume.
Which 2 actions will accomplish this task? (Choose two.)
A. Use the vol create command with a guarantee parameter set to none
B. Use the vol create command with a guarantee parameter set to volume
C. Use the lun create command with the space-reserve parameter set to enabled
D. Use the lun create command with the space-reserve parameter set to disabled
正解：B,C

質問 4：
A new server has been installed in your environment, but it is unable to see its NetApp boot
LUN. You have narrowed the problem down to the zoning on your Cisco switch which has the following configuration:
zone name z_NetAppvsan 400
memberpwwn 20:00:00:25: B5: C0:ff:ee
memberpwwn 50:0a:09:84:8d:7c:51: D5
zoneset name zs_NetAppvsan 400
memberz_NetApp
zoneset activate name zs_NetAppvsan 400
What is the problem with your zoning configuration?
A. The zone and zoneset names do not match.
B. The member does not reference the VSAN.
C. The zoneset was improperly activated.
D. The PWWN for your NetApp LIF is incorrect.
正解：B

質問 5：
You have an AFF A300 system that serves FC LUNs. The LUNs are replicated to a disaster recovery site that has a FAS8200 system that is running SATA drives. There are no FC or FCoE capable switches at the disaster recovery site.
In this scenario, which three actions are required to test the disaster recovery LUNs on the
Ethernet switches? (Choose three.)
A. License FC
B. Enable ISCSI
C. Bind the initiator groups to port sets.
D. Create LIFs
E. Map the LUNs to initiator groups
正解：B,D,E

質問 6：
You want to ensure maximum performance of iSCSI LUNs.
Which statement is correct in this scenario?
A. Configure your network to have Layer 3 switches.
B. Enable flow control on the switch.
C. Use 1GbE instead of 1OGbE.
D. Set the MTU size to 9000.
正解：D

質問 7：
You want to configure iSCSI on a 4-node cluster that only has NFS configured. You need to guarantee that you have at least two optimized paths per LUN.
In this scenario, what are the minimum number of iSCSI LIF needed?
A. 2
B. 8
C. 4
D. 6
正解：B

質問 8：
You are deploying iSCSI on a newly installed ON TAP cluster. Your network administrator has provided you with 10 Gb network links and physically connected them to your nodes.
According to NetApp best practice, which two network settings should you configure to optimize performance? (Choose two.)
A. Enable jumbo frames.
B. Disable jumbo frames.
C. Disable Ethernet flow control for all ports.
D. Use single initiator, multiple target zoning.
正解：A,C

質問 9：
Referring to the exhibit, which zones use only World Wide Port Name Zoning?

A. Jake
B. Bond
C. Zeus
D. Jeff
正解：C